The computer is always dead, and then the boot shows Windows error recovery, what is the problem? Reinstall it.
The computer is turned on to display Windows error recovery, you need to restart the computer. After the user has started the power-on self-test, immediately press the F8 key on the keyboard to select the first item and enter the Safe Mode. Press the following method to set the computer to boot cleanly. After that, restart the computer again to see if you can smoothly enter the operating system desktop. If not, users should restore, restore or reinstall the operating system as follows.
[example] Screenshot
computer starting up the Advanced Boot Options menu (in English):
computer Power advanced boot options menu (Chinese):
1 ,. after into safe mode, follow the steps below, set the system clean boot method is as follows:
a), click on the Start menu and type msconfig in the search box, then press Enter. Alternatively, press the “Win+R” key on the keyboard at the same time, type msconfig, and then click “OK” (or press Enter).
[Example screenshot]
b) Click on the "Services" tab and select "Hide all Microsoft services". Then, click "Disable All".
[Example Screenshot]
[Prompt Description]: Temporarily disable third-party system service items, just In order to prevent problems when the system starts these third-party system service items, the system startup problems are encountered. This action does not affect the operating system. Later, users can manually restart these third-party system service items by manually starting them.
c) Click on the "Startup" tab, then click on "Disable All" and confirm.
[Example screenshot]
[Prompt description]: Temporarily disable all boot self-start items, just to prevent boot load from booting When the item is launched, the system starts to encounter problems. This action does not affect the system or other programs. In the future, users can manually enable these boot-ups by manually starting them.
e) When the "System Configuration Utility" pops up, select "Do not show this message again" in this dialog box, and click "OK". then restart your computer.
[Example screenshot]
2, after the user repairs the system error, the setting is restored from the "clean boot" state to the "normal boot" mode. the method is as follows:
a), click on the start menu, and type msconfig in the search box, then press enter. Alternatively, press the “Win+R” key on the keyboard at the same time, type msconfig, and then click “OK” (or press Enter).
[Example screenshot]
b) On the "General" tab, click "Normal startup - load all device drivers" and service".
[Example screenshot]
c) Click on the "Start" tab, then manually check the check to make sure there is no problem. Start the item and confirm it.
[example] Screenshot
d), click "OK" button to close the window. When prompted to restart your computer, click Restart. Alternatively, the user manually restarts the computer so that the modified system boot entry takes effect.
[Example screenshot]
E), specific settings and implementation of the system clean boot method, please click on the following URL, go to see Microsoft Help and help in the help:
1, http://support.microsoft.com/kb/331796/en-us
< Br>2, http://answers.microsoft.com/zh-hans/windows/forum/windows_vista-performance/answers/424b4486-464c-4169-979c-db4d80f6abab
f ), users can also manually perform system repair or system restore in safe mode.
[Example screenshot]
3. If the computer is turned on, even the security mode cannot enter, or, when entering the security mode, A blue screen will appear. This indicates that the operating system has been completely damaged. In this case, the user is no longer able to manually repair the operating system. At this point, the user is required to use the system backup to restore the system after troubleshooting the hardware. If there is no system backup in the computer when the system is intact, you need to completely reinstall the operating system.
4. Use the U disk boot disk to reinstall the operating system.
[The rookie white will also install (reload) the detailed tutorial of the operating system]
Users make their own U disk boot disk . The methods and steps for installing (reinstalling) the operating system are as follows:
1. Users need to download the system installation image file first, either the original version (installed version) or the GHOST version. It can be stored in the U disk boot disk or hard disk. [Note: If the system installation image file already exists in the user's computer, this step is skipped]
[Note]: The system installation image file saved in the computer, do not Stored in the partition where the system is to be installed (for example: C drive).
2. Download Chinese cabbage Super U disk boot disk creation tool v4.5_Default PE boot (recommended). Or, download the computer store one-button U disk boot disk creation tool _v3.4. Run after installation. The user can make a U disk boot disk with one click.
3, users can also use the floppy disk (UltraISO) virtual CD-ROM software, select to open the ISO format system installation image file. In the above menu bar, select → "Start) →" written to disk image "→ Select U disk, U disk boot disk can be produced.
exemplary screenshot] [
[Note] U disk format option to create a boot disk, to tell you
motherboard
BIOS supports USB format is consistent. otherwise, the computer will not boot to start using the U disk boot disk , enter the system installation interface or enter the WinPE system.
4, press the DEL button ( notebook
computer generally press the F2 button, pay attention to the boot self-test prompt or view Computer or motherboard manual), into the BIOS, change the first boot item from hard disk to USB flash drive. Then, insert the USB flash drive boot disk. Press F10 again to save the settings and restart the computer (or manually select the user → save the settings and restart Start).
5, the user uses the U disk boot disk, boot the computer into PE (WinPE). Use GHO hard disk installer (or GHOST32, one key GHOST) Software, select the installation image GHO file, restore the image to the C drive. Follow the prompts to restart the computer, refer to step 4 above, enter the BIOS, put the first startup item, U hard disk instead. Save the settings, restart the computer. Select into just installed (heavy equipment) systems, complete all subsequent installation and setup. Computer operating system is installed (reinstall) is complete.
[Remarks] Use GHOST version to install (reload) the system without formatting the C drive in advance.
6. If the image installation file is ISO format, the following two types can be used. Installation method:
a), directly use the virtual CD-ROM software to load the ISO image to the virtual CD-ROM drive, system installation (reload).
b) Use WinRAR to decompress the image with the suffix name ISO. For the GHOST version, refer to step 5 above for system installation (reload). If it is the original version (installed version), run the unzipped directory (folder). Setup.exe, system installation (reload).
7, after the system is finished, remove the U disk boot disk. Restart the BIOS, change the first boot from U disk to Hard disk. Then, save the settings. Restart the computer. Normal boot, into the system just installed (reloaded). Complete system, device driver, commonly used Subsequent mounting member other items. Until all subsequent installation and after setting, the operating system is installed (heavy) as well.