Win7 system computer printer will cause jamming and processing methods

First, the printer jam causes:

Paper jam is one of the most common printing faults in daily printing. The main causes of paper jam are the following three:

1. Use inferior paper or paper to get wet

If there is no problem with checking the printer parts, the biggest problem is paper problems. Inferior paper is often accompanied by a lot of paper scraps, and paper scraps fall into the machine during the printing process, which puts pressure on the pickup roller and increases the possibility of paper jams.

1. Paper is too light and easy to jam

Especially when printing on both sides, the paper has been deformed after one heating and ink penetration printing. If the paper weight is lower than this time 60 grams, then it is prone to paper jams. The paper is damp, the paper is wet, and the paper jam is easy to appear.

2, use inferior paper or paper dampness

Second, the software configuration problem

If the software settings are wrong, there will be a paper jam, for example, the carton is placed It is paper of other sizes, but the A4 size paper is still set in the software settings, so paper jams will occur. Sometimes it is neither a hardware problem nor a software problem. There is no paper inside the printer, but the printer still prompts for paper jam. At this time, you can do a clear memory operation, and the method of clearing the memory operation is also very simple. Press “Feed+Cleaning+Power”, then press “Cleaning>10 seconds.

Third, spare parts aging

If a printer has been used for more than one and a half years, the parts will start to age, especially the pickup roller, the pickup roller and the separation claws. Wear, this is also the main cause of paper jams. If the paper has just entered the machine, it will jam. This phenomenon is generally caused by the wear and tear of the pickup roller to make the printing paper not in place. If the wear is not serious, use a damp cloth to scrub and clean it several times. If it is used for a while, it will malfunction again. At this time, you still don't want to change the pickup roller. You can try to handle the pickup roller slightly, and then smash the holster on the pickup roller and turn it 180 degrees. Or take the holster and wrap it around a few times and put the holster on it to make it thicker to offset its wear. If you use it for a while and then fail again, you will have to replace the pickup roller to completely solve the problem.

For laser printers, the pickup roller is also the most wearable part of the printer. When the paper in the paper tray is normal and the paper cannot be taken, the pickup roller is often worn or the spring is loose. There is not enough pressure to feed the paper into the machine. The pickup roller is worn out and cannot be replaced at one time. The rubber band can be used for emergency treatment. After winding the rubber band, the friction of the crepe paper is increased, and the paper feeding can be restored to normal.

4. After the printer jams the paper extraction process:

Note:

If you need to turn off the printer to remove the jam during printing, press Resume/Cancel before turning off the printer. The button cancels the print job.

1. Turn off the printer, and then unplug the printer from the power outlet.

2. Open the top cover.

IMPORTANT:

1. Do not touch transparencies (A) or white seat belts (B).

2. If the paper or hand touches these parts and smears or scratches them, the printer may be damaged.

3. Make sure there is no paper jam under the print head holder.

4. If there is a jam under the printhead holder, move the printhead holder to the right or left edge of the easy-to-remove paper.

5. While moving the printhead holder, grasp the top of the printhead holder and slowly slide it to the right or left edge.

6. Hold the jammed paper with your hand.

7. If the paper is curled, pull it out.

9. Pull the paper out slowly to prevent it from tearing, then pull the paper out.

9. Make sure that all jams have been removed;

10. Close the top cover;

11. All print jobs in the queue will be canceled. Please print again if necessary.

Warm reminder:

1. When reloading paper, be sure to use paper suitable for printing and load it correctly into the printer.

2. When printing resumes after removing all jammed paper, if there is information about the jam on the computer screen, paper fragments may remain in the printer.

3. In this case, make sure there are no pieces of paper left in the printer.

The above is the cause and method of paper jam in the win7 system computer printer. If the paper cannot be removed or the paper is torn in the printer, or the paper jam continues after the paper is removed, please contact the service center. contact. Hope can help everyone.