IE can't open the solution to the problem that the site has terminated operation

First, the problem of network settings

This reason is more likely to manually specify the IP, gateway, DNS server networking, and use a proxy server to access the Internet. Double check your computer's network settings.

Second, DNS server problem

When IE can't browse the webpage, you can try to use IP address to access first. If you can access it, it should be a DNS problem, causing DNS problems. If you get DNS error or DNS server itself when you are connected to the network, you can manually specify the DNS service (the address can be the DNS server address provided by your local ISP, or you can use the DNS server address elsewhere). In the properties, (Control Panel - Network and Dial-up Connection - Local Connection - Right-Click Properties - TCP /IP Protocol - Properties - use the following DNS server address). Different ISPs have different DNS addresses. Sometimes it is a router or network card problem, and can't connect with the ISP's DNS service. In this case, you can turn the router off for a while or reset the router.

Another possibility is that there is a problem with the local DNS cache. In order to improve the speed of website access, the system will automatically store the website that has accessed and obtained the IP address into the local DNS cache. Once the website is accessed again, the website will be taken out from the local DNS cache without going through the DNS server. The IP address is accessed. Therefore, if there is a problem with the local DNS cache, the website will be inaccessible. You can rebuild the local DNS cache by executing ipconfig /flushdns in Run.

Third, the problem of the IE browser itself

When the IE browser itself fails, it will naturally affect the browsing; or IE is maliciously modified and destroyed will also lead to the inability to browse the web. At this time, you can try to repair with "360 Guardian IE Repair Expert" (recommended to fix in safe mode), or reinstall IE

Fourth, the problem of network firewall

If the network firewall is not properly set If the security level is too high, accidentally put IE into the blocked access list, wrong firewall policy, etc., you can try to check the policy, reduce the firewall security level or directly turn off and try to restore normal.

Five, network protocol and network card driver problems

IE can not browse, it may be caused by network protocol (especially TCP /IP protocol) or network card driver damage, you can try to re-network card driver and Network protocol.

Six, HOSTS file problems

HOSTS file is modified, it will also lead to browsing is not normal, the solution is of course to empty the contents of the HOSTS file.

VII. Problems with system files

When the system files related to IE are replaced or damaged, it will affect the normal use of IE. At this time, you can use SFC command to fix it. WIN98 system SFC can be executed in "Run" and then scanned; WIN2000/XP/2003 is executed in "Run" by sfc /scannow.

When only IE can't browse the webpage, and QQ can be on, it is often caused by damage or loss of files such as winsock.dll, wsock32.dll or wsock.vxd (VXD only exists under WIN9X system). Winsock is an important part of the TCP/IP protocol. Generally, the TCP/IP protocol is reinstalled. However, xp begins to integrate TCP/IP protocol, so it can't be reloaded as easily as 98. You can use the netsh command to reset the TCP/IP protocol to the state it was in when the operating system was first installed. The specific operation is as follows:

Click "Start Run", enter the "CMD" command in the run dialog box, pop up the command prompt window, and then enter the "netsh int ip reset c:\ esetlog.txt" command. Enter, where the "resetlog.txt" file is the log file used to record the results of the command execution. The parameter option must be specified. The full path of the log file specified here is "c:\ esetlog.txt". The result of executing this command has the same effect as deleting and reinstalling the TCP/IP protocol.

Tip: The netsh command is a command line based scripting tool that you can use to configure and monitor Windows systems. It also provides an interactive network shell interface. The format of the netsh command is available. See the help file (you can type "netsh/?" in the prompt window).

The second solution is to repair the above files, WIN9X uses SFC to re-extract the above files, WIN2000/XP/2003 uses sfc /scannow command to repair files, when using sfc /scannow can not be repaired, you can try online WinSockFix, a repair tool for this issue, can be downloaded and searched online.

Eight, anti-virus software real-time monitoring problems

This is not often seen, but sometimes it is related to real-time monitoring, because the real-time monitoring of anti-virus software has added monitoring of web content. To give an example: Rising will cause IE to be unable to browse the webpage on a few machines (many friends have encountered it). The specific performance is that as long as the webpage monitoring is turned on, IE will not be able to browse the webpage after about 20 minutes of booting. At this time, if Rising's webpage monitoring is turned off, everything will return to normal; after completely reinstalling Rising, it cannot be solved. Although not every machine that installs Rising will have this problem, after all, the system of each machine is different, and the installed programs are different. But if IE can't browse the web, you should also check the anti-virus software.

Nine, Application Management service problems

can only appear on the QQ can not open the web page, just restart after the game. However, even if you restart, you can't open the webpage after 7 to 8 webpages, you can only go to QQ. Sometimes telecommunications often let you disable the Application Management service and you can solve it. The specific reasons are unknown.

10. Infected with a virus

This situation is often manifested in the IE interface in the lower left box when prompted to open the page, but the old half did not respond. View the process in the task manager, (enter the method, put the mouse on the taskbar, right click - task manager - process) to see how the CPU occupancy rate, if it is 100%, you can be sure that it is infected with the virus, At this time, you want to run other programs is simply a crime. This is to check which process greedily takes up CPU resources. Once found, it is best to record the name, and then click the end, if you can not end, you must start to delete the Dongdong in safe mode, but also enter the registry, (method: start - run, enter regedit) in the registration In the table dialog box, click Edit - Find, enter the name of the program, find it, click the right mouse button to delete, and then search several times, often can be completely removed.

There are a lot of viruses, antivirus software can't do anything, the only way is to manually delete

11, check if the system is forbidden to download:

Download restrictions can be made through the Internet Control Panel, Group Policy, Registry to limit downloads

Check IE: User Configuration--Administrative Template--Internet Explorer--Security Features--Restrict File Download Check

Check Registration Table (in the run input regedit): Windows Registry Editor Version 5.00[HKEY_CURRENT_USER\\Software\\Microsoft\\Windows\\CurrentVersion\\Internet Settings\\Zones\\3]@="""1803"=dword:00000003