Win8 system uses bearer network to share wireless to realize mobile Internet access

Operation steps: 1. First confirm that the wireless network card switch is turned on, the driver has been successfully installed, and the wireless network function can be used normally. Open Control Panel --- View network status and tasks, click on the "Change Adapter Settings" on the left side, confirm that there is a "Wi-Fi" network connection. As shown below:

desktop & ldquo; computer & rdquo; right click of selecting & ldquo; disposed & rdquo ;, click & ldquo; device manager & rdquo ;, or press & ldquo; Windows & rdquo; key and & ldquo ;X” key, select "Device Manager", confirm "Network Adapter" under the device with no exclamation mark, there is a wireless network card device and "Microsoft Kernel Debug Network Adapter", as shown below (different brands The model wireless network card name is slightly different. The following figure uses the Atheros AR9285 as an example. If you do not have these two devices, please uninstall the existing wireless network card driver and reinstall the Lenovo website to provide the wireless network card driver.

If the down arrow icon, right-click the device select Open. As shown below:

If there is an exclamation mark with "wan miniport", please refer to the note explanation.

click on the network icon in the lower right corner of the taskbar, if other networks around the signal, wireless network card is the emergence of a usable state.

2. determine whether to open a network share related services. You can right click on the desktop < computer> icon, open “ management & rdquo;---<quo;services and applications & rdquo;---"service” (or simultaneously press “ windows and R keys & rdquo ;, enter “services.msc”, click OK to open “Service Manager”), check to see if <;Internet Connection Sharing (ICS)" and "Remote Procedure Call (RPC)" If “manual"not" is running”, right click on the corresponding service <;start”;if “disable”, corresponding service right click on “property",“start mode&rdquo ; set to “automatic", click the "application" button, click “start”, then click “OK" to complete the setup.

3. Set the carrier network. Press the Windows and X keys at the same time and select “Command Prompt (Administrator)”.

Enter netsh wlan set hostednetwork mode = allow ssid = you want to create a network name (English format) key = you want to set a password (at least 8) Press Enter to set ssid and password . (E.g. netsh wlan set hostednetwork mode = allow ssid = mywlan key = 12345678.)

input netsh wlan start hostednetwork, press Enter to open the carrier network.

4. Set a network share in order to open the Control Panel --- --- View network status and tasks Change adapter settings

If the above command to create a successful, there will be a “Local connection*” behind a digital network connection. And the middle part will display the set wireless network name. As shown below:

& ldquo in; right click and select & ldquo;; Ethernet & rdquo click Properties & rdquo ;, & ldquo; & rdquo ;, sharing arrangement shown in FIG. Press, click & ldquo; determining & rdquo; The button saves the settings. (If you use a broadband connection to dial-up Internet access, please click “Select Properties” to set the share in the “Broadband Connection”)

After the above operation is completed, the wireless network created by the mobile search “mywlan” is used. Key "12345678" rd connection test. Remarks: If the network icon in the lower right corner is turned on, “Wi-Fi” is displayed as “Off”. 2. If the Device Manager appears “WAN Mini Port (Network Monitor)” 3. Enter the command and press the enter key. Found that there is no "local connection*" in the "Change Adapter Settings" interface, first open “Device Manager" again to see if there is a "Microsoft Managed Network Virtual Adapter" disabled, as shown below . If it is disabled, right-click and select “Enable”, then re-enter the command to create a wireless network. (Note: This virtual device can only occur after the creation of a bearer network, under normal circumstances is hidden, invisible)

If the above is done, still does not appear & ldquo; Local Area Connection * & rdquo ;, please Open “Control Panel"-“System and Security"-“Windows Firewall", click on the left side" Allow Programs or Features via Windows Firewall", find the "Windows Communication Foundation" project to see if all Check the box, click OK after all, and try to re-create the wireless network.

If the phone is connected to a wireless network created by the network, but can not open the page, first of all computer protection software installed temporarily close or suspend protection, and then open the & ldquo; Control Panel & rdquo; --- & nbsp; System & Security "---“Windows Firewall", click on the left side <; turn Windows Firewall on or off", this is temporarily set to off, then the phone will re-open the web page to try.

If the end of the phone QQ can send and receive messages, but can not open the page, other applications can not be networked computer system may malfunction DNS service available in & ldquo; Change Adapter Settings & rdquo; in the & ldquo; Ethernet & rdquo; or " "Broadband connection" (depending on the way you use the network) right-click to select "status", click "details", record the "IPv4 DNS" information, manually set in the mobile network settings “DNS server" (domain name) address. For details on how to set up, please refer to the instructions provided by the mobile phone manufacturer.

may also consult the local network operator for the DNS server addresses. The following public NDS server addresses can be used: 114DNS (114.114.114.114, 114.114.115.115), Google Public DNS (8.8.8.8, 8.8.4.4), OpenDNS (208.67.222.222, 208.67.220.220), depending on the region and use Network operators choose nearby.