Ultra-capacity burning skills

With the development of digital products and broadband networks, CD recorders have become a necessity for many users due to their lowest unit cost, large storage capacity, simple operation and long shelf life. At present, the market of optical magnetic recording, the market of DVD recorders can be described as booming. The DVD burners below 1,000 yuan do not seem to be news. The industry has predicted that most DVD recorders will fall below the thousand yuan to become mainstream at the end of this year. Forecasting is predictive, but from the current price positioning and development of DVD recorders and discs, it is not easy to popularize at the end of the year or early next year, so CD burners are still the preferred products for consumers in current magneto-optical recording. .

CD burners have been developed for so many years, I think everyone is very comfortable with burning CDs, but in the process of using it will always encounter such problems, with a 700MB CD-R disc burning, compare The common thing is that after downloading the DVDrip movie, I want to save it in a good collection. But often after the movie file is added with the subtitle file, what can I do if I can't put a 700M disk in the normal way? It is impossible to disassemble a DVDrip movie into two files. Even if it can be opened, it is a waste of space and is difficult to keep. If you want to burn the data on a disk, what should you do? The answer is to use super engraving to achieve! So, what is super engraving?

In fact, the outer edge of each CD-R disc often leaves some room, and the optical material is evenly applied evenly, so you can find ways to use these extra storage space. The most commonly used Nero Express burning software also provides the ability to burn in these parts beyond the normal recording range. With this function, more than the limited amount of data is burned on a CD-R disc, which is over-burning. That is super-engraved. Because the super-engraving has a certain risk factor, it is very likely that the CD-R disc will be abolished if it is not engraved. If you master the correct method of over-engraving, you can smoothly "engage" another piece of heaven and earth. The following is the specific operation process of the editor when the CD-R disc is over-engraved. It is also a matter of experience, even if everyone exchanges it!
disc test

First you will you buy a blank CD-R disc into the CD burner, select NeroCDSpeed ​​program, select the drop-down menu, disc overburning test, this is your super Prepare the work that must be done before burning. After

test window appears, as well as basic information on the disc, including capacity, time, manufacturers, and other types of discs, select start to start the test.

Burn opportunity analog over-burn process, do not worry this is just a simulation, not really burn go. Upon completion, a prompt box will appear stating that the total time the disc can be overwritten and the time more than normal, and ask if you want to save the data, this is your optional YES save.

finally will pop up a message box, green indicates normal burn part, yellow can overburn section, the following are the specific parameters, choose Close to close the exit.
Actual combat stage

After the analog recording, I realized that the platter has the ability to be super-engraved. Now I have to enter the actual stage, because the software and hardware have the necessary conditions for super-engraving, you can follow The following steps are super-engraved.

1. Start burning software Nero Express, click on "More" and select "Settings" in the extended options.

first pop-up settings dialog box, and then open the open the "Advanced Properties" tab.

select the "Enable overburning function" check box, and the estimated total capacity "maximum length" After setting the text input box excess RW disc after fitting the data to the total amount of space as the burning excess ( Converted to expressed in time). After the above settings are selected, click the “OK” button to return to the main interface of the burning software, and then you can use the normal burning program for over-engraving.

But one thing to note is that, before burning sure to select "CD time recording (DAO)", added later allowed here do not tick at the file, and check the disc after burning tick data (for insurance For the sake of this, reduce the risk factor to a minimum) and then click on the More option.

closed Select CD-ROM, CD-ROM and select the write-once mode (DAO) is.

The following is the burning process. It is not difficult to super-burn CD-R discs. The most important thing is that you can do more with less money, which is full of DIY fun. Not for it? Finally, there are a few things to note before superburning:

1. Your recorder must have the ability to support over-engraving, so you must first check if your recorder supports over-engraving;

2, the burning software you use must support over-burning, the current commonly used burning software Nero, most of the software included with the CD burner Nero Express supports over-burning;

3, you use The actual capacity of the recorded disc is greater than the nominal value. You can view it with Nero CDSpeed ​​in Nero Express. It is recommended that you choose a better quality disc, which makes it easier to successfully achieve overburning.

There is also the choice of the platter is equally important, the better quality of the disc is conducive to over-engraving, and the poor quality of the disc will not only be burned, but also easy to damage the recorder. Therefore, if conditions permit, it is recommended to choose some brands of discs when purchasing. At present, the unit price of a single sheet in the disc market can be selected to some good brand discs, such as: Ritek (Chad), Benq ( BenQ), golden time and so on.