What does the broadband connection fault code mean?

First, WindowsXP comes with dialing software error message 1.Error691 The user name and password entered are incorrect, and the connection cannot be established. Cause: The username and password are incorrect; the ISP server is faulty. Workaround: Use the correct username and password and use the correct account format provided by your network service provider. 2.Error797 ADSLModem connected device was not found. Cause: The ADSLModem power supply is not turned on; there is a problem with the cable or network cable between the network card and the ADSL Modem; the corresponding protocol is not properly bound after the software is installed; an incorrect empty connection is established when the dial-up connection is created. Solution: Check the power supply and cable; check the network properties, and the PPPoE-related protocol is correctly installed and properly bound; check the dial-up connection properties to see if you have used an “ISDNchannnel-AdapterName?xx” device, the device For an empty device, you should choose the correct PPPoE device to replace it, or re-create the dial-up connection. Second, RasPPPoE dialing software error message 1.Error645 NIC does not respond correctly. Cause: The NIC is faulty or the NIC driver is faulty. Solution: Check the network card and reinstall the NIC driver. 2.Error678 cannot be connected to the ISP server. Cause: The server of the ADSL network service provider is faulty, or the ADSL telephone line is faulty. Solution: Check if the ADSL signal lights are properly synchronized. 3.Error691 The user name and password entered are incorrect and a connection cannot be established. Cause: The username and password are incorrect, the server of the network service provider is faulty Solution: Use the correct username and password and use the correct ISP account format. 4.Error791 ADSLModem connected device not found. Cause: The ADSLModem power supply is not turned on, the network cable and the ADSL Modem cable or the LAN cable are faulty. After the software is installed, the corresponding protocol is not properly bound. An incorrect empty connection is established when the dial-up connection is created. Solution: Check the power supply and cable; check the network properties, and the PPPoE-related protocol is correctly installed and properly bound; check the dial-up connection properties to see if you have used an “ISDNchannnel-AdapterName?xx” device, the device For an empty device, you should choose the correct PPPoE device to replace it, or re-create the dial-up connection. 5.Error602, Error633 Dial-up network cannot be connected because the device is installed incorrectly or is in use. Cause: RasPPPoE is not fully or properly installed. Solution: Uninstall all PPPoE software, protocols, and reinstall. Third, Enternet500 dialing software error message 1.E0040P Cause: ADSLModem power is not turned on; the cable or network cable between the network card and ADSLModem has a problem; the corresponding protocol is not properly bound after the software installation; the wrong connection is established when creating the dial-up connection Empty connection. Solution: Check the power supply and cable; check the network properties, and the PPPoE-related protocol is correctly installed and properly bound; check the dial-up connection properties to see if you have used an “ISDNchannnel-AdapterName?xx” device, the device For an empty device, you should choose the correct PPPoE device to replace it, or re-create the dial-up connection. 2. E0037P The user name and password entered are incorrect and the connection cannot be established. Cause: The username and password are incorrect; the server of the network service provider is faulty. Workaround: Use the correct username and password and use the account format provided by your network provider. Enternet300 or Enternet500 In general, there are three main types of error messages: E0037P: Loginfailed, makesureyouhaveenteredcurrectusernameandpassword! Problem: Username and password are incorrect. Solution: See the "User Name and Password for FTTB Users" in the top. E0040P: Timeouttoconnectserver Problem: The connection server timed out. Solution: In this case, please check if the network connection in the room is normal, is the network card light on? If there is no problem, please call 63192188 to report the obstacle. E0041: Failedoncreateadapter(device) Problem: Creating an adapter (device) failed. Solution: This is a problem with your dial-up software. You must uninstall Enternet300 or Enternet500 (uninstall method: open “my computer”→“control panel”→“add remove program”, find Enternet300 or Enternet500, double click and start uninstalling). After uninstalling, restart and then re-install Enternet300. If this is still the case, it is recommended that you switch to other dial-up software such as RasPPPoE. Note: If the XP operating system cannot install Enternet300 or Enternet500, an error message of E0041P will appear. Windows XP comes with dial-up software Error 678: Unable to connect to the remote computer. Problem: Trying to connect to the server failed Solution: Please check if the network connection in the room is normal, is the network card light on? If there are no problems, then I am sorry, there is a problem with our network, you can only report the error 691: Access is denied due to invalid username or password on the domain. Question: ………… are written so clearly Solution: Still see the top of the "User Name and Password for FTTB Users" Error 619: Unable to connect to the specified server, the port used for this connection has been shut down. Problem: The server has not responded to your username and password because the last connection error occurred and the redial interval was too short. Solution: It is recommended that you try again after one to two minutes. Error 769: Unable to connect to the specified target. Question: This means that there is a problem with your computer's network device. Solution: Open “My Computer”→“Control Panel”→“<quo;Network Connection”, Check if the local connection is in“ Disable the status, just double-click on the local connection and see the status changes to “enabled” If there is no local connection, then your network card is 100% problematic —— not installed or broken. Please contact your computer supplier or solve it yourself. Note: After successfully connecting to the Internet, you will see icons for two computers in the lower right corner of the screen. If you want to disconnect the network: Enternet300 or Enternet500: Right click on the icons of the two computers and click “Disconnect”, then click “Exit” XP dial-up connection: Right click on the icons of the two computers and click “disconnect” If the error message displayed during dialing is not within the above range, or if you are not familiar with the operation of reinstalling the dial-up software, please consult 63192188. Added: After opening the enternet300 dialing software, only the top blue bar is popped up, and the interface for entering the account password cannot be displayed. There are two solutions to this problem: (If there is no special requirement for the input interface, you can also operate this way (right click on the blue icon in the lower right corner of the taskbar) and click on the left button.) 1. Solve Method 1 Enter the installation directory of enternet300 (usually in programfilesEfficientNetworksEnterNet300app or programfilesntsEnterNet300app), open the file enternet.ini, and find a line of commands under [WindowSize]: Rect=0304013206090424 (this line number is undefined) add * before the line command (asterisk ) Save it. 2, the solution 2 Enter the installation directory of enternet300 (usually c: programfilesntsapp), rename the enternet.ini to enter enter1.ini). Then double-click the desktop Enternet300 shortcut, the system will automatically clear the original ADSL dial-up connection because the original ini file can not be found, that is, only the "createnewprofile" icon is left in the open window. The next thing to do is to re-establish a dial-up connection, then double-click on it, the previous problem will be solved, and a new enternet.ini file will be created automatically in the installation directory.