Many friends now want to learn network cloning technology. But there are so many articles on network cloning that are not so accurate. Therefore, the BIOS repair website should be requested by the netizens to make detailed use steps.
The files used in this document can be downloaded at the end of the article.
Make a network clone image: Mount the system disk directly on the network clone server. Note that the system disk must be set to the slave disk. The network clone program must be installed on the master disk of the network clone server. The network clone server must have enough hard disk space on the hard disk. You can use the second hard disk to create a clone image file.
Hang another hard disk ready on your machine. After rebooting into DOS mode, start GHOST and select "Local→Disk→To Image
screen.width-333)this.width= Screen.width-333" border=0>
screen.width-333)this.width=screen.width-333" border=0>
Select the system disk that needs to be mirrored. Press Enter to select the partition that has enough space (here we choose the second physical hard disk).//This article comes from the computer software and hardware application network www.45it.com reproduced please specify
screen.width -333)this.width=screen.width-333" border=0>
screen.width-333)this.width=screen.width-333" border=0>
At this point the system prompts for the mirror The file starts with a name, here we are BAK. Press the Enter key, the system will prompt you to choose the compression method. Select NO is not compressed. FAST is fast compression. HIGH is high compression ratio. In fact, you need to choose at will. Choosing HIGH will save space, but it may waste time.//This article comes from the computer software and hardware application network www.45it.com reproduced please specify
screen.width-333)this. Width=screen.width-333" border=0>
After selecting, press YES to perform the backup operation.
screen.width-333)this.width=screen.width-333" border=0>
Because FAT32 format partition can only recognize 2G files, so every time you reach 2G, you will be prompted to re-establish File.
screen.width-333)this.width=screen.width-333" border=0>
After the image file backup is complete, we should create the GHOST server. Start WINDOWS to open GHOSTSRV. EXE file. The file can be found in the GHOST Enterprise Edition. (In fact, the BIOS repair website forum has already provided the download)
Give the server a name. My name is shenzi//This article comes from the computer software and hardware application network www. 45it.com reproduced please specify
Select the clone client, then select the image file we just backed up to another hard drive, click to accept the customer's button.
screen.width-333)this.width=screen.width-333" border=0>
The system will automatically find the client at this time.
screen.width-333)this.width=screen. Width-333" border=0>
Now the job we have to do is set up the client.
In the directory where the GHOST file is located, we need to create a WATTCP. CFG file. This file is the designated IP and gateway. If there is no such file, GHOST will automatically scan the DHCP server. It is not recommended to use DHCP server. So we use DOS command, EDIT to create a WATTCP. CFG file.
In the directory where GHOST is located, enter the edit space wattcp.cfg
screen.width-333)this.width=screen.width-333" border= 0>
In EDIT, we create the following content
IP=IP specified by your machine. To avoid duplication, try to use the machine number.
NETMASK=Subnet mask, set according to IP rules .
GATEWAY=Gateway. This is the IP address of the GHOST server.
screen.width-333)this.width=screen.width-333" border=0>
After the creation is complete, save the file After that, exit EDIT. Then run the 8139 network card DOS environment driver. Execute RTSPKT space 0X60, 0X60 is an interrupt to the network card. Here must give the network card an interrupt. Otherwise it is unable to drive your network card. I use the interrupt is 0X60. Oh, in fact, this is only One method, the easiest way is to run the GO batch file directly, which is a batch of NIC driver and GHOST automatically added, which is more convenient.
screen.width-333)this.width=screen. Width-333" border=0>
Run GHOST. Select MULTICASTTING
screen.width-333)this.width=screen.width-333" border=0>
At this point the system will ask you the server name Enter your server name here (here here). Press Enter (
screen.width-333)this.width=screen.width-333" border=0>
Select the hard drive you want to recover. Press Enter
screen.width-333)this.width=screen.width-333" border=0>
Here you can re-edit the partition size, if there is no special requirement, select OK to continue.
screen .width-333)this.width=screen.width-333" border=0>
Then select YES and confirm the start.
screen.width-333)this.width =screen.width-333" border=0>
At this point our client has entered the receiving state.
screen.width-333)this.width=screen.width-333" border=0>< Br> At this point, we go to the GHOST server to see it. Under normal circumstances, the server can already see the IP address and MAC address of the client. After connecting all the clients, you can choose to start the network for network cloning. .
screen.width-333)this.width=screen.width-333" border=0>
But remind everyone that the network GHOST machine should not exceed 50. If there is a problem, then the trouble is you Oh. If the machine is disconnected, please turn off the machine and wait for it. After about 5 minutes, it will be recorded as timeout. GHOST will continue to run. In addition, some NIC drivers will lock the keyboard after execution. Please build your own batch. The file is fine.
Note:
1, Ghost network clone, mainly the client settings. If you are unable to connect or the server cannot find the client, first check the client's settings.
2. When setting up the client NIC, you must specify an interrupt to the NIC. The NIC is on the client and must be installed with the DOS driver.
3, if you want to be convenient, you can use the server version of the operating system, do a DHCP (dynamic IP allocation) server, then you do not need a machine to configure the IP of a machine, just do a batch Just fine, and finally add a -rb parameter (automatically restart after completion)