Why can't the computer move without moving the mouse?
The following is the reason why the mouse suddenly stops moving:
< Br>1. The host is too old, there are a lot of accessories worn out or even lose function, the most likely is the CPU,
graphic card
. 2. Heat dissipation problem (very likely), due to CPU or motherboard
overheating, there will often be a card machine phenomenon, and then directly crash. 3. Hard disk problem, you can consider that the hard disk interface is loose (very likely), it is recommended to pull out the re-plug, or the power supply of the hard disk is insufficient (possibly small) 4. CPU usage is too high and problems occur, also because of the computer The configuration is too old, so that the current configuration can not keep up with the program, often run more programs and it is easy to crash. 5. The host memory is not enough. It is recommended to add a memory stick. Memory is a big factor affecting the smooth running of the machine. If the memory is not enough, it is very likely to crash. It is recommended to buy a memory stick and add 2G to the memory. 6. Memory modules are not compatible (possibility is small) 7. Software problems. Software conflicts cause the computer to crash (not likely, because the landlord reinstalled the system) Note: This type of problem is a crash, not just the mouse can not move.
Personal advice: When the mouse does not move, you should first consider the hard disk interface or interface line.
The problem of mouse is mostly the problem of the mouse itself. You need to go to another computer to do the test, first eliminate the problem of the mouse itself. If it is a system, please fix the system (repair the driver that comes with the system). 1. Press F8 to enter the safe mode and exit. Select Restart or Shutdown to boot, you can enter the normal mode (fix the registry). 2. If the fault persists, please use the system restore that comes with the system to restore it to the time you did not have this fault (if the normal mode fails to recover, please press F8 to enter the safe mode and use the system restore). 3. If the fault persists, use the system disk repair, open a command prompt and enter SFC /SCANNOW Enter (there is a space between SFC and /), insert the original system disk repair system, the system will automatically compare and repair. 4. If the fault persists, set the CD-ROM drive in the BIOS to insert the system boot disk into the first boot device and press R to select “Repair Install”. 5. If the fault persists, it is recommended to reinstall the operating system.
If the mouse does not move, the keyboard can't be controlled, and prove that your machine is dead or poisoned. Please restart the machine and kill the virus. See the best antivirus software for antivirus.
If the mouse does not move, the keyboard can also be used to check if the plug is loose. Sometimes it will fall off due to tension. 3, the new mouse does not move, with a long mouse, the more difficult to use, the last did not move.
Solution: The new mouse does not move. If the CD comes with the mouse, please install the software of the CD. If you still don't move, go to the buyer to change the mouse or test the mouse. The mouse has been used for a long time, and it will inevitably get some dust. Open the top cover of the mouse and clean the dust inside. If the mouse with the rubber ball is the easiest to use due to dust, unscrew the dome, remove the rubber ball, and clean the dust on the axle. The reason why the mouse does not work properly and the solution summary: In the normal use of the computer, we will always encounter some minor problems, which will bring us some unpleasant episodes using the computer. In fact, it is nothing more than summing up the following points. Below I will summarize the problems of several abnormal work of the mouse in the process of using the computer, I hope to give you some tips. 1. Some old users still retain the serial mouse because of computer upgrade or business reasons. This kind of mouse can be used normally on any kind of motherboard with COM interface, but due to the technical content of the graphics card in the new years, especially the graphics card after GeForce2 MX, the graphics card takes up more interrupt resources, sometimes it will grab Interrupt with the COM port. So when this happens, hardware conflicts will occur, and the mouse will not work properly, jitter, and so on. If we upgrade the old machine, it is best to use the PS/2 mouse, which will cause the mouse to work abnormally afterwards, causing trouble for everyone. 2. Interference from external radioactive signals Some people who know a little about hardware know that computer hardware enters work at a certain frequency when it is working. Computers at work are most susceptible to external radioactive signals and cause abnormal work. Sometimes we find that the mouse has frequency jitter, accompanied by frequency wave sound and display jitter, which is mostly due to external strong radioactive signals. For example: high-power appliances and their lines, mobile phones
signals and so on. To solve this kind of problem, we just need to keep the computer away from these things. If space is limited, we can connect a UPS or a voltage regulator rectifier in front of the computer line. This kind of problem is mostly related to the power supply system. You can troubleshoot according to the following methods: 1. If you use WinXP, set the shutdown to STR/STD (suspend to memory/suspend to hard disk), then start again after entering the system. The USB device may not be powered properly due to the advanced
Power
management function. Please log in to WinXP with the management account, right click on "My Computer", and then click "Properties" to enter the "Device Manager" on the "Hardware" page. Find the USB controller in the Device Manager and expand to see the "USB Root Hub" option. Double-click to open, and then remove the hook before the "Allow computer to turn off this device to save power" option in the "Power
Management" page. 2. If the above method does not work, enter the power management option of the motherboard BIOS and change the advanced power management mode from S3 (STR) to S1 (POS). 3. If you use a passive USB Hub and the mouse is connected to the USB Hub, it may also cause insufficient power supply. Because in the passive USB Hub, all USB interface power is obtained from a USB interface. If a 4-port USB Hub is connected to 4 USB devices, then each USB port can only get 500mAh/4=125mAh power supply. If this is the case, you can try to unplug several USB devices! Reminder: Regarding the above tutorial, "How to do if the mouse does not move, what is the reason why the mouse suddenly does not move", I believe that as long as you follow the above methods, you will soon find the mouse that suddenly stops moving. Reasons
Br>
It should be a problem with the host computer. My computer has some problems on some days. It’s a good time to rehabilitate it.
Connection problems
There is a problem with the mouse
Mouse USB contact is not good, try another port
It should be a problem with your mouse connection, USB mouse? Either change the interface or change the mouse.
The mouse is not good, look at the mouse